« previous next »
Pages: [1] |   Go Down

Author Topic: Torx Size on Front Bumper??  (Read 1584 times)

Offline Ultramag

  • Level 2
  • **
  • Posts: 124
Torx Size on Front Bumper??
« on: 08/12/07 - 06:10PM »
I am going to pull my factory front bumper off tomorrow and it looks to be attached with some large torx...........what size is this??  Where is the best place to get a torx to remove these?
Logged

Offline Ultramag

  • Level 2
  • **
  • Posts: 124
Re: Torx Size on Front Bumper??
« Reply #1 on: 08/12/07 - 06:13PM »
Is it a T55??
Logged

Offline TJ-2thousand

  • Level 4
  • ****
  • Posts: 907
  • When in doubt, throttle out!!!
Re: Torx Size on Front Bumper??
« Reply #2 on: 08/12/07 - 06:14PM »
yeah its a T55.
Logged
CAMPING WITHOUT BEER IS JUST SLEEPING OUTSIDE!

Offline TanYJ

  • Level 4
  • ****
  • Posts: 706
Re: Torx Size on Front Bumper??
« Reply #3 on: 08/12/07 - 11:06PM »
I think i got mine from sears.  Get the black one over with the impact drivers (not air impacts, the percussion type), or prep the threads with a liberal amount of PB Blaster the night before you try.  Good luck, they're a beyotch.
Logged
J-ust.................It's
E-mpty.............Hip
E-very............To be
P-ocket.........[-]====[-]
.....The second mouse gets the cheese.....
"Skinny models, you can keep those..I like big corn-fed mid-western ho's"

Offline cpj

  • Level 2
  • **
  • Posts: 123
Re: Torx Size on Front Bumper??
« Reply #4 on: 08/13/07 - 12:56AM »
All I can say is that it sucks to be you. Mine were a whore to get loose.
Logged
Once in a while that perfect part rolls around that the redneck craftsman sees and goes, "this would be just perfect as a ________."

Offline Ultramag

  • Level 2
  • **
  • Posts: 124
Re: Torx Size on Front Bumper??
« Reply #5 on: 08/13/07 - 08:34AM »
there are times when it comes in handy to have 280 lbs. to put behind something...........this was one of those times.  they were on tight but not bad at all to bust loose.
Logged

Offline TanYJ

  • Level 4
  • ****
  • Posts: 706
Re: Torx Size on Front Bumper??
« Reply #6 on: 08/13/07 - 09:42AM »
LOL, nice, mine hadn't been touched since it rolled off the line in Aug. of '87, and it took my fat arse, a 3# ball-peen hammer, an impact, and about 2 hours to get mine out.
Logged
J-ust.................It's
E-mpty.............Hip
E-very............To be
P-ocket.........[-]====[-]
.....The second mouse gets the cheese.....
"Skinny models, you can keep those..I like big corn-fed mid-western ho's"

Offline freds_94

  • Level 3
  • ***
  • Posts: 442
Re: Torx Size on Front Bumper??
« Reply #7 on: 09/ 5/07 - 02:29PM »
what you need to do is send the wife/girlfriend to O'rielly's and the guys there will end up doing it for you.
Logged
trying to raise a teenager is like nailing jello to a tree
Pages: [1] |   Go Up
« previous next »